 |
|
|
Click
on drawing to view large scale version
|
| |
| SmartFan
AC-J is available for 115 or 230 VAC PSC or shaded pole
fans and blowers with current ratings up to 3.5 Amps. AC-J operates
at either 50 or 60 Hz power line frequency as selected by a
jumper on the board. Control Temperature is selected by means
of a jumper. AC-J is compatible with temperature sensors P1
thru P9 shown on Sensors
page. |
| |
|
Features
- Current rating
is 3.5 Amps in air stream, 2.0 Amps in still air
- Selectable Control
Temperatures of 35°, 40° or 45°C (74°, 80° or 86°C with
P3 surface sensor)
- Models optimized
for PSC or shaded pole air movers
- Compact size
|
| |
UL recognized to UL508 and CSA-C22.2, File E100344 |
 IEC
950, VDE 0806 approved TUV Rheinland File E77132 |
| |
| SPECIFICATIONS |
| |
|
Part
Number
|
Power
Line Voltage
|
Maximum
Current to Fans (1)
|
Fan
Type
|
|
Nominal
|
Range
|
200
ft/min
|
Still
Air
|
|
|
115
VAC
|
95-135
VAC
|
3.5
Amps
|
2.0
Amps
|
PSC
Shaded Pole
|
|
|
230
VAC
|
190-270
VAC
|
3.5
Amps
|
2.0
Amps
|
PSC
Shaded Pole
|
|
H101
|
Hardware
Pack
|
|
| (1)
Air Temperature of 55°C or less. See page 13 for derating above
55°C. U.S. Patents 4,659,920, 4,722,699 and 5,364,026 |
| |
| INSTALLATION |
| |
|
Mounting
|
| To satisfy
safety agency requirements (UL, CSA, IEC, VDE), allow 1/4" (6.3
mm) between the circuit board and chassis ground and 5/16" (8
mm) to any uninsulated secondary circuits. To satisfy UL, a
normal blow fuse rated 10 Amps or less should be used in the
power line circuit. |
| |
| Sensor
Selection |
| There
is no polarity consideration when connecting the sensor. Click
here to view Sensors page: Sensors |
| |
| CONNECTIONS
/ JUMPERS |
|
|
Figure
1 Wiring Diagram
Click
on drawing to view large scale version
|
|
| |
| OPERATION
|
| |
| Fan
Speed vs. Sensor Temperature |
| The
relationship between fan speed, as a percentage of full speed,
and sensed temperature is shown in Figure 2. Full speed occurs
at the Control Temperature (Tc ). |
|
Figure
2
Fan speed vs. sensor temperature
|
 |
|
| |
| Settings
|
| Control
Temperature (J4): Use this jumper to set control temperature
(Tc ) to 35°, 40°, or 45°C. Factory setting is 40°C. If the
P3 sensor is used, Control Temperature settings are 74°, 80°,
and 86°C. |
| Line
Frequency (J3): Use this jumper to set the line frequency
to 50 or 60 Hz. Factory setting is 60 Hz. |
| |
| Testing
|
| If operated
at reduced speeds, the rotational speed of AC fans is sensitive
to static pressure load. Fans should be installed and working
against the intended system resistance before checking idle
speed. Most fans will idle well above one-half speed if they
are not loaded. |
| |
| SUGGESSTED
CONECTING HARDWARE |
| |
|
Ref.
Desc.
|
Header
on Board (1)
|
H101
Hardware Pack
|
|
|
Quantity
|
Description
|
Manufacturer
(1)
|
PartNumber
(1)
|
|
J1
|
39-28-1043
|
|
Housing
Terminal (tin)
|
|
|
|
J2
|
22-29-2021
|
|
Housing
Terminal(gold)
|
|
|
|
|
4
|
PCB Support
|
Richco
|
CBS-4-19
|
|
| (1)
or equivalent |
